• €180

• 26 diseños

• 13 diseñadores

---

Resumen de Diseño de Empaque

We need a PSD file for a product packaging. We need to redesign to a new brand. Please look at the attachments to this project. We have attached the briefing. You want to find everything you need to start the project. Briefing for Liquid Patch What do we need? We need a design for product packaging. The height of the packaging is 16.7 cm. The width is 8.9 cm. It's about a tube that contains a PVC liquid. This product is available in 10 different colors. The design must be based on the design of the website: https://www.lotu.de. 2. Specifications 2.1. Dimensions - Height: 16.7 cm - Width: 8.9 cm 2.2. Design colors RGB: ffce00 RGB: 222222 RGB: 000000 RGB: ffffff On the front page is the product. The tube takes 6.5 cm from the right edge. The name of the product is Liquid PVC. The name of the website is www.lotu.de. Please use our logo. The website URL is: www.lotu. DE Please use these Icons in your design: Suitable for: Two Actions Clean and apply surface Wait for maximum strength in 24 hours The Backside On the back are information Liquid PVC is used to repair damaged areas such as holes or cracks made of materials such as PVC (inflatable boats, inflatable air mattresses and rubber boots), neoprene (diving suits) and the like ), Polyester (tents) Eco Leather (bags and shoes) Since inflatable products lose air pressure due to small holes in their use, the Liquid PVC is particularly well-suited for densification of these holes Holes can be compacted in a short procedure 2. Key points High elasticity UV-resistant High adhesive strength Temperature-resistant Greater resistance to damage 3. Usage Application (title) Degrease and clean the repair site carefully. Shake the contents of the tube thoroughly. This is important so that the color pigments are included in the Liquid Patch. Apply a thick layer to the repair site. Do not worry about the unevenness, it flattens out when drying. For a clean application, we recommend the previous masking with the adhesive tape 352 SE 2091 (sold separately). After applying the Liquid Patches, remove the tape IMMEDIATELY. Do not wait until it dries. For cracks greater than 2 cm or materials that are not tear-resistant due to a lack of backing, use a NG-08 mesh (sold separately). The Liquid Patch alone is not tear resistant. By using a mesh fabric, the repaired site becomes tear resistant. When repairing the inflatable boat must be pumped out. There must be no air leakage from the hole during repair, otherwise it would destroy the Liquid Patch. Let it dry for 24 hours. FINISHED. The dinghy is fully operational again. 4. Safety regulation Safety instructions (title) The Liquid Patch irritates the eyes. In case of contact with eyes, rinse immediately with plenty of water and seek medical attention. Repeated exposure can result in brittle or cracked skin. Be careful not to inhale the vapors. These can lead to tiredness and dizziness. The Liquid Patch should not get into the hands of children. This product should be stored in the original container in a cool, well-ventilated place. Keep the Liquid Patch away from sources of ignition and do not smoke near it. The waste and containers must be disposed of in a secure manner and must not be allowed to enter drains. Use only outdoors or in well-ventilated areas. Wear protective gloves, respiratory protection and eye protection. The manufacturer / supplier is not liable for direct or indirect damage caused by improper use of the product offered. Expiration date: see backside below. Attention: The date on the tube is the date of manufacture. Not to be confused with the expiry date. Storage and Use (Title) Store at temperatures not exceeding 35 ° C. Repair at ambient temperature of 10 to 35 ° C. Repairs must be carried out in a well-ventilated room. When freezing, use only after complete thawing and shaking of the tube. 5. Barcode Please use a placeholder for the barcode 6. Qr Code Please use a placeholder for the Qr Code 7. Composition Solvent, PVC suspension, plasticizer, dye. 8th. Made in Made in Ukraine for Lotu Heerdter Lohweg 212 40549 Dusseldorf Germany 49 (0) 211 50661662 8. Transport class Transport class: UN 1133 - Class 3.2 F1 9. Content of the Tube Content: 20ml

---

Mira y siente

Cada control deslizante ilustra las características de la marca del cliente y el estilo que debe comunicar el diseño de tu logotipo.

---

Requisitos

Debes tener

• The design must be based on the design of the website. The design must have the exact colors as our website. The fonts the website uses: akaChen and Lato. Please use there fonts in your design.

---

Archivos

Descargar todos los archivos - 7,3 MB